Tap Drill Size Chart

1-1/8-12 Tap Drill Size

Tap drill

1-3/64″ 1.0469 in26.59 mm

Use a 1-3/64 in drill (1.0469 in, 26.59 mm) for 72.1% thread.

The drill size for a 1-1/8-12 tap is 1-3/64 in (1.0469 in / 26.59 mm). If you are wondering what size drill bit a 1-1/8-12 tap needs, that is the one: it leaves 72.1% of thread, which is the figure standard tap and drill charts are built around. Below are the other holes you might want for this size - a larger drill for tough material, the form-tap hole, and the clearance holes for the bolt that goes in.

Every drill for 1-1/8-12

Tap drills and clearance drills for 1-1/8-12 (UNF (Unified fine), 12 TPI). Percent of thread is the figure stored for each drill, which reproduces from the major diameter and TPI of 1-1/8-12.
Use Drill Decimal in mm % thread
Standard tap drill Cut tap, general use (standard chart drill) 1-3/64″ 1.0469 26.59 72.1%
Metric substitute Closest metric drill if you have no inch set 26.5 mm 1.0433 26.50 75.5%
Hard material Stainless, tool steel, anything that fights the tap 1-1/16″ 1.0625 26.99 57.7%
Form (roll) tap Theoretical 1.0882 in - starting point, check your tap maker's chart 1-3/32″ 1.0938 27.78 —

Clearance holes for a 1-1/8-12 bolt

A clearance hole is not tapped. It is the hole in the part the bolt passes through, so it is always larger than the thread.

Clearance holes for 1-1/8-12 per ASME B18.2.8. Clearance depends on the bolt diameter alone, so every 1 thread shares these figures.
Fit Drill Drill in Hole min in Hole max in Hole mm
Close 1-5/32″ 1.1562 1.156 1.164 29.36–29.57
Normal 1-7/32″ 1.2188 1.219 1.235 30.96–31.37
Loose 1-5/16″ 1.3125 1.312 1.337 33.32–33.96

1-1/8-12 dimensions

Nominal dimensions for 1-1/8-12. The basic internal minor diameter is the hole a 100% thread would start from, which is why no tap drill is ever that small.
Dimension Inch mm
Major diameter 1.125 28.58
Basic internal minor diameter 1.0348 26.28
Pitch (1 / TPI) 0.0833 2.12
Threads per inch 12 TPI

What the hole looks like

Cross-section of a 1-1/8-12 tapped hole, drawn to scale The drilled hole is 1-3/64″, 1.0469 inches or 26.59 millimetres across. The tap cuts outward from that wall to the major diameter of 1.125 inches. A 100 percent thread would reach in to the basic minor diameter of 1.0348 inches, shown as a dashed line; the difference is why this drill gives 72.1% of thread. major 1.125 in drill 1-3/64″ · 1.0469 in dashed = 100% thread at 1.0348 in
1-1/8-12 in section, to scale. The accent line is the thread the tap cuts from a 1-3/64″ hole; the dashed line is where the crest would sit at 100% thread. The gap between them is the 27.9% of thread this drill leaves behind.

Work out a different hole for 1-1/8-12

Pre-filled with 1-1/8-12. Change the material, the tap type, or which drills you actually own, and it picks the closest real drill and tells you the percent of thread you end up with. The tables above are the published figures and do not depend on this.

The general-purpose target

Tap type
Drills you have

Best drill you have, cut tap, 70% target

1-3/64″1.0469 in26.59 mm72.1% thread

Theoretical hole 1.0492 in (26.65 mm)

One size down, deeper thread26.5 mm 1.0433 in · 75.5%

One size up, easier tapping1-1/16″ 1.0625 in · 57.7%

For comparison, the published chart drill for 1-1/8-12 is 1-3/64″ at 72.1% thread.

Notes on 1-1/8-12

Finest pitch at this diameter
1-1/8-12 is the finest of the standard pitches at 1 in. Fine threads suit thin walls and joints that see vibration, but the hole size matters more: the window between a weak thread and a broken tap is narrower than on 1-1/8-7.
Not the same as 1-1/8-7
1-1/8-7 and 1-1/8-12 share a 1 in major diameter but not a pitch, and they take different drills: 63/64 in for 1-1/8-7, 1-3/64 in for 1-1/8-12. The taps and the fasteners are not interchangeable.
What the standard drill gives you
1-3/64 in leaves 72.1% of thread (standard chart drill). That is in the normal 65-80% band most shop charts aim for.
Stainless, tool steel and other tough material
1-1/16 in opens the hole to 57.7% engagement. Less material for the tap to cut means less torque and less heat, at the cost of some thread depth.
Using a form (roll) tap
A form tap displaces metal instead of cutting it, so it needs a larger hole: 1-3/32 in, against a theoretical 1.0882 in. Treat that as a starting point and check your tap maker's chart.
Closest metric size
M30 x 3.5 is the nearest metric thread by diameter (30 mm against 28.58 mm). It is a planning reference only. The two are not interchangeable: the pitches differ, and a bolt from one will not run into a hole tapped for the other.

Related sizes

Same diameter, different pitch

Next size up and down

Closest metric size

M30 x 3.5 26.5 mm · 1.0433 in · 77.0% 30 mm major against 28.58 mm

Not interchangeable. M30 x 3.5 is the nearest size by diameter, nothing more. The pitches differ, so a M30 x 3.5 fastener will not run into a 1-1/8-12 hole and forcing one will strip both.

Guides for tapping 1-1/8-12

Longer reads on the decisions behind the numbers above.

All guides →

1-1/8-12 tap drill: common questions

What size drill bit do I need for a 1-1/8-12 tap?
A 1-3/64 in drill, 1.0469 in / 26.59 mm. That leaves 72.1% of thread, which is the standard chart figure for 1-1/8-12.
What is the drill size for a 1-1/8-12 tap in mm?
The 1-3/64 in tap drill measures 26.59 mm. If you only have metric drills, 26.5 mm is the closest, giving 75.5% thread.
What drill should I use for 1-1/8-12 in stainless steel?
Use 1-1/16 in instead of 1-3/64 in. It leaves 57.7% of thread rather than 72.1%, so there is less material for the tap to cut and less chance of snapping it.
Is 1-1/8-12 the same as 1-1/8-7?
No. Both are 1 in threads, but the pitch differs, so the drills differ: 1-3/64 in for 1-1/8-12 and 63/64 in for 1-1/8-7. The taps and the fasteners are not interchangeable.
What is the clearance hole for a 1-1/8-12 bolt?
For a normal fit, 1-7/32 in (1.2188 in), with the finished hole between 1.219 in and 1.235 in per ASME B18.2.8. A clearance hole is not tapped; the bolt passes straight through it.
A 4 × 6 in card with the drills for this size.